Search results

...was due to Singer<ref name=singer1990>Singer, S, "Realization of Loss Free Resistive Elements", ''IEEE Transactions on Circuits and Systems'', Vol. CAS-37, No. ...r and a suitable control circuit. The LFR is a two-port element that has a resistive [[Current–voltage characteristic|i-v curve]] at the input terminals. The po ...

...er#Energy losses|losses in the windings and cores of transformers]] due to resistive heating and magnetic losses caused by [[eddy current]]s, [[hysteresis]],<re <ref name="PL">{{cite web |title=Power losses in wound components |newspaper=Info.ee.surrey.ac.uk |url=http://info.ee.surrey.ac.uk/Workshop/a ...

...the image method is zero loss in the [[passband]] (assuming ideal lossless components). Again, this cannot be achieved in practice because reflections from the ...inations diagram.svg|thumbnail|600px|center|An arbitrary image filter with resistive end terminations. Because the terminations are not the image impedance, the ...

...iven below it is assumed that the generator and load impedances are purely resistive (though not necessarily equal) and that the attenuator circuit is required [[Category:Resistive components]] ...

...-Technical-Description.pdf ET-DSP Technical Description 3-Phase Electrical Resistive Soil Heating for the Remediation of Contaminated Soil and Groundwater]{{dea ...temperature of the soil and groundwater by conducting current through the resistive connate water that fills the [[porosity]] of the soil. The increase in temp ...

...er, using the PEEC circuit, it is easy to exclude capacitive, inductive or resistive effects from the model when it is possible, in order to make the model smal ...ner. Moreover, since the final model consists of circuit elements, various components can easily be excluded from the circuit to simplify the problem while the a ...

[[Resistive heating]] of a conductive material implanted in the thermoplastic melts the ...last2 = Bersee|first2 = H.E.N.}}</ref> For example, PEEK and PEI Laminate components for use in [[United States Air Force|U.S. Air Force]] aircraft and a GF-PPS ...

...al structure (generally a wire or a film) onto the sample to function as a resistive heater and a [[resistance temperature detector]] (RTD). The heater is drive ...The measured voltage will contain both the fundamental and third harmonic components (ω and 3ω respectively), because the Joule heating of the metal structure i ...

...t in the board thickness and the presence of other circuits and electronic components, it is not possible to reach a high value of the magnetic dipole. ...as long as sufficient [[Electric power|power]] is available to match the [[resistive]] load of the coils. In Earth orbit, sunlight is one such practically inexh ...

...e other filters can be derived from it by applying a scaling factor to the components of the prototype. The filter design need thus only be carried out once in f It can readily be seen that to achieve this, the non-resistive components of the filter must be transformed by: ...

...ef>{{cite journal |last=Moffatt |first=H. K. |year=1964 |title=Viscous and resistive eddies near a sharp corner |journal=[[Journal of Fluid Mechanics]] |volume= ...oblem by the cylindrical coordinates <math>(r,\theta)</math> with velocity components <math>(u_r,u_\theta)</math> defined by a [[stream function]] such that ...

...ver a range to obtain the impedance spectrum. The resistive and capacitive components of impedance are determined from in phase and out of phase current response ...

...tude of the incident wave if the terminating impedance is wholly or partly resistive since some of the energy of the incident wave will be absorbed in the resis When both <math> Z_0</math> and <math> Z_\mathrm{L}</math> are purely resistive then <math>\mathit{\Gamma}</math> must be purely real. In the general case ...

...ly true, for instance, when short pieces of line are being used as circuit components such as [[stub (electronics)|stubs]]. A short line has very little loss an ...es will be the cause of [[Reflections on copper lines|reflections]] from a resistive line termination. This is another undesirable effect. The [[nominal imped ...

...romagnetic]] material is likely to be non-reciprocal. Examples of passive components deliberately designed to be non-reciprocal include [[circulator]]s and [[Is An example of reciprocity can be demonstrated using an asymmetrical resistive [[Attenuator (electronics)|attenuator]]. An asymmetrical network is chosen ...

;[[Resistivity]], <math>\rho</math>: Specific resistance, as for usual resistive materials, important because of eddy currents; SI units, ohm-metres (Ω·m); These parameters used e.g. in Philips' handbook <ref>Philips' handbook ''Components and materials'', Part 4a, Nov 1978, said in accordance with IEC401 and IEC1 ...

A memristor is a resistive device whose resistance changes as a function of the history of the applied .... However, because of Kirchhoff's laws, the evolution of networks of these components becomes utterly complicated, in particular for disordered neuromorphic mate ...

...rying behavior. This generally occurs when the load drawing the current is resistive. ...6}}</ref> Using [[complex number]]s is a way to simplify analyzing certain components in [[RLC circuits]]. For example, it is very easy to convert these between ...

...especially ones consisting entirely of [[Passivity (engineering)|passive]] components, it can be ambiguous which variables are inputs and which are outputs. In [[file:Resistive divider2.svg|thumb|upright=0.7|Voltage divider circuit]] ...

...ondition for which the [[electrical reactance|reactance]] vanishes but the resistive [[electrical impedance|impedance]] of an [[electrical circuit]] is none the ...F) of any [[Linear system|linear dynamic system]] composed of many coupled components will in general display distinctive resonance-antiresonance behavior when d ...